The Peugeot 208 I was built from 2012 to 2019.
For this generation we cover 6 engines and 41 known faults, each with the mileage range where it usually appears.
The most expensive known risk is high oil consumption: it usually appears at 60,000–200,000 km and costs €150–3,500 to fix.
In UK roadworthiness tests in 2024, at 50–100 thousand km this model most often failed on: lights, wipers and visibility (13.3 %), body and corrosion (7.9 %), tyres and wheels (5.8 %). It fails more often than an average car of the same age and mileage on: lights, wipers and visibility, body and corrosion, exhaust, emissions and leaks. It fails less often than average on: suspension.
Faults typical of this model ✓ Checked against sources (10/2026)
Touchscreen freezes, goes blank or stops responding
usually 20,000–160,000 km · Medium risk
Signs: Screen freezes or stays black, radio, Bluetooth, sat-nav and settings become unusable; sometimes returns after restarting the car.
Fix: Try a reset and the latest software update first; if it keeps failing, repair or replace the head unit / screen.
€50–600
Recall: front wishbone mounting bolts may break
usually 0–200,000 km · High risk
model years 2012–2014 only
Signs: Clunks or vibration from the front end and vague steering; in the worst case a broken bolt affects steering control.
Fix: Check by VIN with a Peugeot dealer that the bolt-replacement recall was done; free of charge.
free / recall
Front strut top mounts / bearings knock
usually 60,000–160,000 km · Wear part
Signs: Knocking from the front over bumps or a creak when turning the wheel at low speed.
Fix: Replace the top mounts and strut bearings in pairs, ideally together with worn shock absorbers.
€150–350
Brake discs wear out earlier than average
usually 80,000–200,000 km · Wear part
Signs: Discs worn or ridged at inspection sooner than expected, vibration or noise when braking.
Fix: Measure disc thickness at every service and budget for discs with every second set of pads.
€150–300
Lighting defects at inspection (low beam, indicators, rear lamps)
usually 80,000–250,000 km · Wear part
Signs: Dead bulbs or lamps, often found only at the technical inspection, mostly on cars six years and older.
Fix: Check all lamps before inspection; replace bulbs and inspect bulb holders and connectors for corrosion.
€20–150
Exhaust system rusts through / cracked flex pipe
usually 80,000–250,000 km · Wear part
Signs: Louder, rattling exhaust or blowing noise under the car; inspection failure for exhaust leaks.
Fix: Replace the rusted silencer section or the flex pipe; check the hangers at the same time.
€100–450
Faults by engine
1.0 / 1.2 PureTech (EB) ✓ Checked against sources (10/2026)
Faults and service: Peugeot 208 I with this engine →
Wet timing belt wears early and sheds debris (built to mid-2022)
usually 40,000–140,000 km · High risk
model years 2012–2022 only
Signs: Flaking or swollen belt seen through the oil filler, rubber bits in the oil or filter, later oil pressure or timing warnings
Fix: Measure belt width with the PSA gauge at every service and replace the belt early if it is out of spec; ask a Stellantis dealer about the extended cover (10 years / 175,000 km)
€0–1,500
Oil pickup strainer blocked by belt debris (low oil pressure)
usually 40,000–150,000 km · High risk
model years 2012–2022 only
Signs: Oil pressure warning, noisy valvetrain, cam timing fault codes, limp mode
Fix: Stop the engine at once; drop the sump, clean the strainer or replace the oil pump, clean or replace the VVT and oil pump solenoids and the turbo oil-feed banjo bolt, and fit a new belt
€0–2,500
Brake vacuum pump fails from belt debris (recall)
usually 40,000–150,000 km · High risk
model years 2013–2020 onlyengine codes: EB2DT, EB2DTS, EB2ADT, EB2ADTS, EB2ADTD, EB2DTSD
Signs: Hard brake pedal, little brake assistance, brake or oil pressure warning
Fix: Check open recalls by VIN (2020 campaign for cars built 3/2013–4/2017, 2023 campaign for 4/2017–12/2020); always replace the vacuum pump when a degraded belt is replaced
€0–900
Oil consumption: piston rings (turbo, built 2014 – mid-2018)
usually 60,000–160,000 km · Medium risk
model years 2014–2018 onlyengine codes: EB2DT, EB2DTS, EB2ADT, EB2ADTS, HNZ, HNY
Signs: Oil top-ups between services, blue smoke, misfires from carbon build-up
Fix: Have a measured oil consumption test done at a Stellantis dealer (covered by the extension); outside cover, fit new pistons and rings and rebore oval cylinders
€0–4,000
Oil consumption: oil separator in the cam cover (turbo, 2018–2023)
usually 40,000–160,000 km · Medium risk
model years 2018–2023 onlyengine codes: EB2DT, EB2DTS, EB2ADT, EB2ADTS, EB2ADTD, EB2DTSD
Signs: Oil use between services, oil in the intake, unstable idle, oil seeping at seals
Fix: Check crankcase pressure and the separator membrane; replace the cam cover with the built-in separator (covered by the extension at a dealer)
€0–500
1.5 / 1.6 HDi / TDCi / e-HDi (DV6, 8v / 16v) ✓ Checked against sources (10/2026)
Faults and service: Peugeot 208 I with this engine →
Injector faults on early 8v engines (knocking, jerking)
usually 60,000–180,000 km · Medium risk
model years 2010–2014 onlyengine codes: DV6C, DV6D, 9HP, 9HD, 9HF, 9HL
Signs: Knocking at low revs, jerking in the lower gears, hard cold starts, injector fault codes
Fix: Read the injector corrections and do a return-flow test; recode or replace the faulty injectors
€250–1,400
EGR valve sooting
usually 80,000–200,000 km · Medium risk
Signs: Jerking, black smoke, power loss or limp mode, EGR fault codes; mostly on cars used for short trips
Fix: Clean or replace the EGR valve; cleaning often helps only for a while
€100–600
DPF clogging; Eolys additive runs low (additive systems)
usually 80,000–200,000 km · Medium risk
Signs: DPF or additive-level warning, limp mode after long periods of city driving
Fix: Refill the additive and reset the counter, check the pressure sensor, force a regeneration; clean or replace the DPF if it is full
€100–1,500
1.6 BlueHDi (DV6FC) ✓ Checked against sources (10/2026)
Faults and service: Peugeot 208 I with this engine →
AdBlue (SCR): tank pump unit, filler-cap vent or dosing injector fails
usually 60,000–180,000 km · High risk
Signs: AdBlue or emissions warning with enough fluid in the tank, countdown to no-start, codes such as P20E8, P21C5 or P20EE
Fix: Check the filler cap vent valve first (a new vented cap can cure it if caught early); otherwise the tank with built-in pump is replaced as one unit; also check the AdBlue injector for crystals and the NOx sensor
€100–1,500
Injector faults; leaking injector copper washers
usually 80,000–200,000 km · Medium risk
Signs: Rough or shaky start, jerking on acceleration, injector fault codes (P0200-P0209); puffing or black deposits around an injector
Fix: Read injector corrections and do a return-flow test; replace only faulty injectors; if a washer leaks, fit new washers and clamp early before the seat is damaged
€150–1,400
DPF clogging; additive (Eolys) runs low
usually 100,000–200,000 km · Medium risk
Signs: DPF or additive warning, frequent regenerations, power loss or limp mode after a lot of city driving
Fix: Refill the additive (about every 120,000 km) and reset the counter, check the pressure sensor and the additive pump, force a regeneration; clean or replace the DPF if it is full of ash
€100–1,300
1.4 HDi / TDCi (DV4) ✓ Checked against sources (10/2026)
Faults and service: Peugeot 208 I with this engine →
Injector or high-pressure pump faults: hard starting, smoke
usually 100,000–250,000 km · Medium risk
Signs: Hard or no starting (often when warm), uneven running, smoke, injector or fuel-pressure fault codes
Fix: Read the injector corrections and do a return-flow test; replace the faulty injectors or the pump control valve / pump; change the fuel filter on time and avoid running the tank empty
€300–1,300
Turbocharger wear or failure
usually 100,000–250,000 km · High risk
Signs: Whistling, loss of power, blue or grey smoke, oil in the intake pipes
Fix: Replace or recondition the turbo, and check the oil feed and return pipes and the oil level; keep oil changes on time
€500–1,200
Crankshaft pulley (damper) rubber breaks up
usually 70,000–160,000 km · Medium risk
Signs: Rattle or knock at idle from the belt side, wobbling pulley, auxiliary belt slips or jumps off
Fix: Replace the crankshaft pulley with a quality part and fit a new auxiliary belt; a loose belt can damage the timing belt
€100–300
EGR valve sooting or sticking
usually 80,000–200,000 km · Medium risk
Signs: Power loss or limp mode, jerking, black smoke, EGR fault codes; mostly with city driving
Fix: Clean or replace the EGR valve; on older engines also check the vacuum solenoid and hoses
€100–450
DPF clogging (Euro 5 68 hp with DPF, to 2013)
usually 60,000–180,000 km · Medium risk
model years 2010–2013 only
Signs: DPF warning, loss of power or limp mode, usually after mostly short trips
Fix: Forced regeneration with a diagnostic tool and a longer drive; check the pressure sensor and software; clean or replace the DPF if it is full
€100–1,200
Oil consumption at higher mileage (breather membrane, wear)
usually 120,000–250,000 km · Wear part
Signs: Oil level drops between services, oily intake, sometimes blue smoke
Fix: Check the turbo first, then replace the valve cover with the built-in breather membrane; a compression test shows if the rings are worn
€100–1,500
1.4 / 1.6 VTi (EP3 / EP6, also MINI N12 / N16) ✓ Checked against sources (10/2026)
Timing chain stretch / tensioner wear
usually 60,000–200,000 km · High risk
Signs: Rattle after a cold start, camshaft timing codes, rough running; a jumped chain bends the valves
Fix: Replace the chain, tensioner, guides and sprockets (with the VVT gears if worn); keep the oil level and change intervals short
€600–1,300
High oil consumption (rings, valve stem seals)
usually 60,000–200,000 km · Medium risk
Signs: Oil needs topping up between services, blue smoke on start or under load, oily spark plugs and carbon in the intake ports
Fix: Rule out leaks and the crankcase breather first; then replace valve stem seals (and guides), or rings / bore work if compression is low
€150–3,000
Valvetronic (variable valve lift) or VVT fault
usually 80,000–200,000 km · Medium risk
Signs: Engine light, rough or hunting idle, loss of power and higher fuel use, valve lift or camshaft timing codes
Fix: Diagnose the Valvetronic motor, eccentric shaft sensor and VVT solenoids; check oil level and pressure first; replace the faulty part
€200–900
Coolant leaks: water pump, thermostat housing, expansion tank
usually 60,000–180,000 km · Medium risk
Signs: Coolant level drops, traces at the pump or housing, temperature warning; overheating can damage the head gasket or head
Fix: Pressure-test the system and replace the leaking water pump, thermostat housing or expansion tank; do not drive while it overheats
€150–500
Persistent misfire: valve seat or cylinder head damage
usually 80,000–220,000 km · High risk
Signs: Misfire on one cylinder that comes back after new plugs and coils, low compression on that cylinder, flashing engine light
Fix: Do a compression or leak-down test before buying more coils; the head must come off for valve seat / valve repair; check the cooling system too
€700–1,500
Oil leaks: valve cover, sump, chain tensioner
usually 60,000–200,000 km · Wear part
Signs: Oil traces on the engine and under the car, burning oil smell, oil level drops without smoke
Fix: Replace the leaking gasket or seal; on 2010-2011 engines check the chain tensioner seal and tightness
€80–350
1.6 THP (EP6 turbo, also MINI Cooper S) ✓ Checked against sources (10/2026)
Timing chain stretch / tensioner fault
usually 60,000–160,000 km · High risk
Signs: Rattle for a few seconds after a cold start, later also warm; loss of power, engine light, camshaft timing codes; a jumped or broken chain wrecks the valves
Fix: Replace the full kit (chain, tensioner, guides, sprocket bolt) with the latest-version parts as soon as it rattles; keep oil changes short and the level topped up
€800–1,800
Carbon build-up on intake valves
usually 60,000–150,000 km · Medium risk
Signs: Rough idle, hesitation and misfires, loss of response, engine light; worse with short trips
Fix: Clean the intake valves (walnut blasting) with the manifold off; it builds up again over time
€300–700
High oil consumption
usually 60,000–200,000 km · Medium risk
Signs: Oil level drops fast (up to about 1 L per 1,000-1,500 km), oil warning, blue smoke; low oil then damages the chain and turbo
Fix: Check the oil at every fuel stop and top up; fix leaks and the crankcase breather first; valve stem seals or piston rings if the engine itself burns oil
€150–3,500
High-pressure fuel pump failure
usually 60,000–180,000 km · Medium risk
Signs: Surging or jerking while driving, long cranking or hard hot starts, limp mode, low fuel pressure codes
Fix: Check rail pressure with a diagnostic tool and replace the high-pressure pump (latest version)
€400–900
Coolant leaks: water pump, thermostat housing, hoses
usually 60,000–200,000 km · Medium risk
Signs: Coolant level keeps dropping, sweet smell, traces under the engine, temperature warning or overheating, fan not starting
Fix: Pressure-test the system; replace the leaking water pump or plastic thermostat housing with seals, and the temperature sensor if the fan does not switch on
€150–600
Turbo oil feed pipe leak or turbo failure
usually 80,000–200,000 km · Medium risk
Signs: Oil smell or burning oil on the exhaust side, oil traces at the turbo, whistling, loss of boost, underboost codes
Fix: Replace the oil feed pipe and its seals; if the turbo has shaft play or leaks oil, replace or recondition it together with new oil pipes
€150–1,500
Gearboxes
Manual
Clutch wear
usually 120,000–200,000 km · Medium risk
Signs: Slipping, high bite point
Fix: Replace clutch kit
€500–900
ETG / EGS / BMP / SensoDrive (automated)
Clutch actuator / hydraulic unit
usually 80,000–160,000 km · High risk
Signs: Won't select a gear, 'gearbox fault', jerky shifts
Fix: Repair or replace the actuator; clutch re-learn
€500–1,500
Clutch wear (automated)
usually 80,000–150,000 km · Medium risk
Signs: Slipping, harsh engagement
Fix: Replace clutch + re-learn
€500–1,000
AL4 / AT8 (4-speed automatic)
Pressure-regulation fault: harsh shifts, limp mode stuck in 3rd
usually 80,000–200,000 km · High risk
Signs: Bangs or harsh engagement once warm, 'gearbox faulty' warning and the gearbox stays in 3rd (codes such as P1167 / pressure regulation)
Fix: Check the oil level with the proper procedure first, then replace the pressure-regulating solenoid; if the fault returns, fit a reconditioned valve body and change the oil
€250–1,200
EAT6 / EAT8 (Aisin)
Jerky low-speed shifts and hesitation (software / adaptation)
usually 20,000–240,000 km · Wear part
Signs: Jerks or clunks when slowing down or in town traffic, hesitation when pulling away, flare or slip when cold
Fix: Ask for the latest gearbox software and an adaptation reset; check the oil level and condition
€0–300
Valve body / internal clutch wear from aged fluid (high mileage)
usually 120,000–250,000 km · Medium risk
Signs: Harsh or slipping shifts that get worse over time, dark burnt-smelling fluid, gearbox warning or limp mode
Fix: Change the fluid (several partial changes or a machine change with the correct Aisin / PSA fluid); if shifts stay bad, repair the valve body / solenoids or overhaul the gearbox
€300–3,000
Scheduled service
Intervals and typical prices for the 1.0 / 1.2 PureTech (EB) engine. Other engines differ in oil, timing drive and some filters; the app gives the exact plan.
Roadworthiness tests by mileage
Share of tests in the United Kingdom (DVSA MOT, 2024) that this model failed because of each system. Bold red means more often and green less often than an average car of the same age and mileage. Sample: 178,597 tests.
Roadworthiness tests in the Netherlands by age
Share of this model's Dutch fleet that had a defect in each system at a roadworthiness test (APK) in 2025. Bold red means more often and green less often than an average car of the same age and fuel. Sample: 51,671 cars.
Most common engine versions in the EU
New cars of this generation registered in the EU, Iceland and Norway 2010–2025: 1,487,571, of which 3,038 in Croatia. The share shows how common each version is.
Source: European Environment Agency (EEA), monitoring of CO₂ emissions from new passenger cars, CC BY 4.0. CO₂ and fuel use are official type-approval values (WLTP from 2021), not real-world consumption.
Official recalls
Recalls the manufacturer published in the United Kingdom for this model (33). The same recalls usually apply across Europe. Ask an authorised dealer to check by VIN whether your car is affected and whether the work has been done.
- Other Peugeot 208 Horn sound volume04/06/2026 · R/2026/231
- Lights Emission recall – On Board Diagnostics18/08/2025 · R/2025/344
- Engine / loss of power Peugeot DV5R Engines Camshaft Chain.03/07/2025 · R/2025/246
- Engine / loss of power Peugeot 208- Evaporation test results on EB2FA engines.24/07/2024 · R/2024/292
- Electronics / software On affected vehicles the AC compressor stator wiring could develop a fault leading to current loss inside the AC compressor that could result in a vehicle powertrain shutdown when driving.09/05/2023 · R/2023/140
- Brakes / ABS / ESP On the affected vehicles the operation of the brake vacuum pump may be affected by material detaching from the timing belt caused by the ageing of the engine oil.13/12/2022 · R/2023/045
- Brakes / ABS / ESP On the affected vehicles the operation of the brake vacuum pump may be affected by material detaching from the timing belt caused by the ageing of the engine oil.13/12/2022 · R/2023/035
- Engine / loss of power The open circuit detection system could be over sensitive causing a number of operational issues13/01/2022 · R/2022/012
The other recalls (25) are listed in the app.
Common questions
Does the Peugeot 208 I have a timing chain or a timing belt?
1.0 / 1.2 PureTech (EB): wet belt · 100,000 km / every 72 mo; 1.5 / 1.6 HDi / TDCi / e-HDi (DV6, 8v / 16v): belt · 150,000 km / every 96 mo; 1.6 BlueHDi (DV6FC): belt · 175,000 km / every 120 mo; 1.4 HDi / TDCi (DV4): belt · 140,000 km / every 120 mo; 1.4 / 1.6 VTi (EP3 / EP6, also MINI N12 / N16): chain; 1.6 THP (EP6 turbo, also MINI Cooper S): chain.
What are the known problems with the Peugeot 208 I?
The faults with the highest risk: timing chain stretch / tensioner fault (60,000–160,000 km, €800–1,800); adBlue (SCR): tank pump unit, filler-cap vent or dosing injector fails (60,000–180,000 km, €100–1,500); persistent misfire: valve seat or cylinder head damage (80,000–220,000 km, €700–1,500); clutch actuator / hydraulic unit (80,000–160,000 km, €500–1,500). The full list by engine is on this page.
What does the Peugeot 208 I most often fail its roadworthiness test on?
In UK roadworthiness tests in 2024, at 50–100 thousand km this model most often failed on: lights, wipers and visibility (13.3 %), body and corrosion (7.9 %), tyres and wheels (5.8 %). It fails more often than an average car of the same age and mileage on: lights, wipers and visibility, body and corrosion, exhaust, emissions and leaks. It fails less often than average on: suspension.
What should you check when buying a used Peugeot 208 I?
Before you buy, ask an authorised dealer to check by VIN that the recalls have been done (33 have been published for this model). If the engine has a timing belt, ask for the invoice for its replacement: with no proof, assume it has not been done. On the test drive, watch for these signs: rattle for a few seconds after a cold start, later also warm; adBlue or emissions warning with enough fluid in the tank, countdown to no-start, codes such as P20E8, P21C5 or P20EE. The full checklist is in the guide to buying a used car.
Sources and notes
Main sources for the faults of this model (suspension, brakes, electrics, body, recalls) and gearboxes:
Faults, intervals and prices are indicative and collected from public sources and owner experience; always rely on the service book and a qualified workshop. Test statistics: DVSA – Anonymised MOT tests and results, Open Government Licence v3.0. Dutch tests: RDW Open Data (CC0). Engine versions: EEA, monitoring of CO₂ emissions from new passenger cars (CC BY 4.0, DG CLIMA). Owner complaints: NHTSA ODI (public domain). Recalls: DVSA Vehicle Safety Branch Recalls Database, OGL v3.0. Brand and model names are trademarks of their owners and are used only to describe the vehicles. How we check the data →
Updated 21/11/2026