This app is in testing and development. The information is indicative and may be inaccurate, so check it with a workshop.
VIN Service Planner
Common faults, service intervals and costs

Fiat Panda II

2003–2012 · Fiat Panda 2

2
engines covered
18
known faults
49,294
roadworthiness tests in the statistics
8
official recalls

Enter your VIN and mileage and get a plan built for your exact engine and gearbox.

The Fiat Panda II was built from 2003 to 2012.

For this generation we cover 2 engines and 18 known faults, each with the mileage range where it usually appears.

The most expensive known risk is hydraulic unit failure: accumulator or pump (stuck in neutral): it usually appears at 50,000–180,000 km and costs €250–1,500 to fix.

In UK roadworthiness tests in 2024, at 100–150 thousand km this model most often failed on: suspension (23.9 %), lights, wipers and visibility (22.3 %), brakes (12.8 %). It fails more often than an average car of the same age and mileage on: brakes, suspension, tyres and wheels, body and corrosion, exhaust, emissions and leaks.

Engines

EngineFuelTiming driveOil
1.1 / 1.2 / 1.4 8v & 16v FIREPetrolBelt · 120,000 km / every 60 mo5W-40 · Fiat 9.55535-S2 / ACEA A3 · ~2.8 L · every 15,000 km
1.3 MultiJet / CDTI / DDiS / TDCiDieselChain5W-30 / 5W-40 · Fiat 9.55535-S1 / dexos2 · ~3.2–3.9 L · every 15,000 km

Faults typical of this model

Electric power steering column (Dualdrive)

usually 80,000–200,000 km · Medium risk

Signs: Heavy steering, EPS warning

Fix: Repair or replace the column / sensor

€200–700

Front suspension (top mounts, drop links)

usually 60,000–160,000 km · Wear part

Signs: Knocks over bumps

Fix: Replace parts

€80–250

Faults by engine

1.1 / 1.2 / 1.4 8v & 16v FIRE ✓ Checked against sources (10/2026)

Faults and service: Fiat Panda II with this engine →

Ignition coil pack or HT leads fail (misfire)

usually 60,000–180,000 km · Wear part

Signs: Misfire, rough idle, flashing engine light, P030x codes, sometimes visible sparking at the leads in the dark or wet

Fix: Check plugs, leads and the coil pack; replace the leads as a set with good-quality parts and the coil pack if it is cracked or weak

€50–200

Unstable idle or stalling: dirty throttle body, idle valve or MAP sensor

usually 60,000–200,000 km · Wear part

Signs: Hunting or pulsing idle, stalling when coming to a stop, sometimes worse in damp weather; throttle position fault codes on electronic throttles

Fix: Clean the throttle body, the idle control valve (cable-throttle 1.1 and early 1.2) and the MAP sensor, check the breather hoses, then run the throttle adaptation; replace the throttle body if the position sensor is faulty

€50–350

Crankshaft position sensor failure (cuts out, no start, P0335)

usually 60,000–200,000 km · Medium risk

Signs: Engine cuts out while driving or will not start, often when hot, then restarts after cooling; code P0335

Fix: Read the fault memory, check the sensor plug and wiring, and replace the sensor with a quality part

€50–150

Thermostat leaks past its seal (slow warm-up, P0115 / P0128)

usually 60,000–180,000 km · Wear part

Signs: Temperature gauge stays low, weak heater, fans start early, engine light with coolant temperature codes

Fix: Replace the thermostat (check which of the two types the engine has), refill and bleed the cooling system, and renew old coolant

€60–200

Water pump leaks before the timing belt is due

usually 80,000–160,000 km · Medium risk

Signs: Coolant loss, coolant traces or crust at the pump behind the timing cover, noise from the pump bearing

Fix: Replace the pump together with the timing belt kit; use only a thin bead of sealant on the pump

€200–450

Head gasket failure after overheating

usually 100,000–220,000 km · Medium risk

Signs: Coolant loss without a visible leak, white smoke, mayonnaise under the oil cap, overheating, bubbles in the expansion tank

Fix: Pressure and CO test of the cooling system; replace the head gasket, have the head checked for flatness, and fix the cause (thermostat, pump, fan, leaks)

€400–900

Oil seepage: cam cover gasket and crankshaft seals

usually 80,000–250,000 km · Wear part

Signs: Oily engine, oil drops under the car, oil smell; oil can reach the coil pack area on top of the engine

Fix: Find the leak and replace the cam cover gasket or the leaking crankshaft seal; a rear crankshaft seal needs the gearbox removed

€50–450

1.3 MultiJet / CDTI / DDiS / TDCi ✓ Checked against sources (10/2026)

Faults and service: Fiat Panda II with this engine →

Timing chain stretch and tensioner wear

usually 100,000–200,000 km · High risk

Signs: Metallic rattle from the chain side on cold start, crank/cam correlation fault code, engine light

Fix: Measure the crank/cam deviation with a diagnostic tool; replace the chain kit with tensioner and guides before the chain jumps

€800–1,300

Injector faults or leaking injector seals

usually 80,000–200,000 km · Medium risk

Signs: Hard starting, rough or knocking idle when cold, power loss, higher fuel use, sometimes limp mode

Fix: Read per-cylinder correction values and back-leak; repair or replace only the faulty injector and renew its seal

€200–1,200

EGR valve sooting

usually 80,000–180,000 km · Medium risk

Signs: Engine light, rough idle, hesitation, power loss or limp mode; worse with short trips

Fix: Check EGR movement in live data; clean or replace the valve

€200–500

Turbo variable vanes or actuator sticking

usually 100,000–200,000 km · Medium risk

Signs: Boost fault codes, power loss, limp mode, sometimes whistling or smoke

Fix: Check boost control and charge-air hoses for leaks first; free or replace the actuator, replace the turbo only if it is worn

€150–1,300

Glow plugs or glow plug control unit failure

usually 80,000–200,000 km · Wear part

Signs: Hard starting in cold weather, smoke after a cold start, glow plug warning light

Fix: Test the plugs and the control unit; replace faulty parts (seized plugs may need extraction)

€100–400

Gearboxes

Manual

Clutch wear

usually 120,000–200,000 km · Medium risk

Signs: Slipping, high bite point

Fix: Replace clutch kit

€500–900

Dualogic / Selespeed (automated)

Hydraulic unit failure: accumulator or pump (stuck in neutral)

usually 50,000–180,000 km · High risk

Signs: Longer and rougher shifts, pump runs often or for long, gears drop out while driving, gearbox warning and the car stays in neutral

Fix: Check the hydraulic pressure and fluid level; replace the pressure accumulator first if it has lost its charge, otherwise repair or replace the pump / power unit and bleed the system

€250–1,500

Actuator seal leaks / gear position sensor faults

usually 60,000–180,000 km · Medium risk

Signs: Flashing gear display, delayed or skipped gears, fluid loss from the actuator, gear-sensor or lever-switch fault codes

Fix: Find the leak; reseal the actuator (selector rod O-rings), clean or replace the position sensor, top up with the approved hydraulic fluid and run the calibration

€200–900

Clutch wear beyond adaptation range: judder on pull-away

usually 60,000–150,000 km · Medium risk

Signs: Jerky or juddering pull-away and upshifts, clutch slip, high clutch wear index in diagnostics

Fix: Read the clutch wear index and adaptation values; replace the clutch if outside the range, then reset the wear index and re-learn the kiss point

€500–1,000

Scheduled service

Intervals and typical prices for the 1.1 / 1.2 / 1.4 8v & 16v FIRE engine. Other engines differ in oil, timing drive and some filters; the app gives the exact plan.

ItemIntervalTypical price
Engine oil + oil filterEngineevery 15,000 km or every 12 months€70–150
Cabin (pollen) filterClimateevery 15,000 km or every 12 months€15–40
Brake fluidBrakesevery 24 months€50–95
A/C service (regas + desiccant)Climateevery 24 months€70–150
Air filterEngineevery 30,000 km or every 24 months€15–45
Spark plugsIgnitionevery 60,000 km or every 48 months€50–160
Auxiliary (serpentine) beltEngineevery 120,000 km€70–180
Timing belt kit + water pumpEngineevery 120,000 km or every 60 months€450–900
Coolant replacementCoolingevery 150,000 km or every 96 months€70–150
Manual gearbox oilTransmissionevery 150,000 km€60–130
Front brake padsBrakesusually at 30,000–60,000 km€60–150
Front brake discs + padsBrakesusually at 60,000–120,000 km€150–320
Rear brake padsBrakesusually at 50,000–90,000 km€50–130
Tyres (set of 4)Wheelsusually at 40,000–60,000 km€320–700
Wiper bladesBodychecked at service€20–50
12V batteryElectricalchecked at service€100–220

Roadworthiness tests by mileage

Share of tests in the United Kingdom (DVSA MOT, 2024) that this model failed because of each system. Bold red means more often and green less often than an average car of the same age and mileage. Sample: 49,294 tests.

thousand km0–5050–100100–150150–200200–250250+
Brakes4.8 %8.1 %12.8 %16.0 %20.3 %19.7 %
Suspension11.4 %19.0 %23.9 %25.6 %28.0 %30.6 %
Steering0.5 %1.4 %2.8 %3.8 %4.7 %7.8 %
Tyres and wheels4.8 %7.5 %9.4 %10.8 %12.0 %12.3 %
Lights, wipers and visibility10.1 %15.9 %22.3 %25.6 %29.1 %31.4 %
Body and corrosion1.7 %5.0 %7.7 %9.3 %10.8 %9.9 %
Exhaust, emissions and leaks1.4 %4.1 %6.5 %8.8 %10.9 %13.1 %

Roadworthiness tests in the Netherlands by age

Share of this model's Dutch fleet that had a defect in each system at a roadworthiness test (APK) in 2025. Bold red means more often and green less often than an average car of the same age and fuel. Sample: 53,991 cars.

age (years)12–1415–1920+
Brakes6.5 %12.1 %13.5 %
Suspension12.1 %12.3 %10.2 %
Steering0.8 %1.4 %3.3 %
Tyres and wheels22.0 %21.0 %19.0 %
Lights, wipers and visibility31.0 %30.1 %31.1 %
Body and corrosion0.2 %1.8 %3.6 %
Exhaust, emissions and leaks9.1 %9.4 %9.8 %

Most common engine versions in the EU

New cars of this generation registered in the EU, Iceland and Norway 2010–2025: 402,145, of which 0 in Croatia. The share shows how common each version is.

VersionShareYearsCO₂Fuel use
1.1 / 1.2 / 1.4 8v & 16v FIRE1.2 (1,242 cm³) · Petrol41.8 %2010–2011——
1.1 / 1.2 / 1.4 8v & 16v FIRE1.2 (1,242 cm³) · 51 kW (69 hp) · Petrol32.0 %2011–2011——
1.1 / 1.2 / 1.4 8v & 16v FIRE1.1 (1,108 cm³) · Petrol7.0 %2010–2011——
1.3 MultiJet / CDTI / DDiS / TDCi1.2 (1,248 cm³) · Diesel5.9 %2010–2011——
1.3 MultiJet / CDTI / DDiS / TDCi1.2 (1,248 cm³) · 55 kW (75 hp) · Diesel5.9 %2011–2011——
1.1 / 1.2 / 1.4 8v & 16v FIRE1.4 (1,368 cm³) · 51 kW (69 hp) · Petrol4.8 %2011–2011——
PetrolPetrol1.2 %2010–2011——

Source: European Environment Agency (EEA), monitoring of CO₂ emissions from new passenger cars, CC BY 4.0. CO₂ and fuel use are official type-approval values (WLTP from 2021), not real-world consumption.

Official recalls

Recalls the manufacturer published in the United Kingdom for this model (8). The same recalls usually apply across Europe. Ask an authorised dealer to check by VIN whether your car is affected and whether the work has been done.

  • Lights Headlights may fail29/12/2015 · R/2015/229
  • Steering Loss of steering control13/12/2010 · R/2010/212
  • Steering Loss of steering control10/09/2010 · R/2010/101
  • Fire risk Possibility of fire03/09/2009 · R/2009/078
  • Fuel system Fuel may leak02/09/2009 · R/2009/080
  • Brakes / ABS / ESP Brakes may fail07/12/2007 · R/2007/173
  • Fire risk Fuel may leak29/05/2007 · R/2007/068
  • Brakes / ABS / ESP Engine power may be lost20/04/2007 · R/2007/012

Common questions

Does the Fiat Panda II have a timing chain or a timing belt?

1.1 / 1.2 / 1.4 8v & 16v FIRE: belt · 120,000 km / every 60 mo; 1.3 MultiJet / CDTI / DDiS / TDCi: chain.

What are the known problems with the Fiat Panda II?

The faults with the highest risk: hydraulic unit failure: accumulator or pump (stuck in neutral) (50,000–180,000 km, €250–1,500); timing chain stretch and tensioner wear (100,000–200,000 km, €800–1,300); turbo variable vanes or actuator sticking (100,000–200,000 km, €150–1,300); injector faults or leaking injector seals (80,000–200,000 km, €200–1,200). The full list by engine is on this page.

What does the Fiat Panda II most often fail its roadworthiness test on?

In UK roadworthiness tests in 2024, at 100–150 thousand km this model most often failed on: suspension (23.9 %), lights, wipers and visibility (22.3 %), brakes (12.8 %). It fails more often than an average car of the same age and mileage on: brakes, suspension, tyres and wheels, body and corrosion, exhaust, emissions and leaks.

What should you check when buying a used Fiat Panda II?

Before you buy, ask an authorised dealer to check by VIN that the recalls have been done (8 have been published for this model). If the engine has a timing belt, ask for the invoice for its replacement: with no proof, assume it has not been done. On the test drive, watch for these signs: longer and rougher shifts, pump runs often or for long, gears drop out while driving, gearbox warning and the car stays in neutral; metallic rattle from the chain side on cold start, crank/cam correlation fault code, engine light. The full checklist is in the guide to buying a used car.

Other generations

Fiat Panda III 2012–

Models with the same engines

These models share engines with this car, so they share some of its faults too.

Fiat 500 2007–Opel Corsa D 2006–2014Opel Astra J 2009–2015Opel Astra H 2004–2010Fiat Grande Punto / Punto 2005–2018Fiat Punto II 1999–2010Ford Ka II 2008–2016Opel Meriva B 2010–2017

Other Fiat models

Fiat Idea 2003–2012Fiat Croma II 2005–2011Fiat Stilo 2001–2007Fiat Doblò I 2000–2010Fiat Ducato III 2006–2014Fiat Sedici 2006–2014Fiat Bravo II 2007–2014Fiat Linea 2007–2015Fiat Fiorino / Qubo 2008–Fiat Multipla 1998–2010

Sources and notes

Faults, intervals and prices are indicative and collected from public sources and owner experience; always rely on the service book and a qualified workshop. Test statistics: DVSA – Anonymised MOT tests and results, Open Government Licence v3.0. Dutch tests: RDW Open Data (CC0). Engine versions: EEA, monitoring of CO₂ emissions from new passenger cars (CC BY 4.0, DG CLIMA). Owner complaints: NHTSA ODI (public domain). Recalls: DVSA Vehicle Safety Branch Recalls Database, OGL v3.0. Brand and model names are trademarks of their owners and are used only to describe the vehicles. How we check the data →

Updated 21/11/2026